FAQs
To Reboot:
- Use the end of a paperclip to press and hold the reset/ reboot button for 3-5 seconds until the LED blinks white to show a successful reboot.
- If the feeder successfully reconnects to your Wi-Fi with internet, the LED will blink blue and then turn solid showing it is fully connected and operational.
How do you reset the time on a PetSafe feeder? ›
To Set Time: 1. After powering feeder, the LCD will show a blinking 12 for time format setup. Use UP or DOWN buttons to scroll to select 12 hour or 24 hour time format. Press RIGHT button to set time.
Why is my PetSafe automatic feeder not working? ›
Feed Now Not Working/Jammed
Clean the feeder. Replace the batteries with four, new D-cell alkaline batteries. Important: Use only alkaline batteries in the feeder. Press the sleep button on the back of the feeder to resume the programmed feedings.
How to reconnect a pet feeder? ›
Go the pet feeder' settings page, look for “remove device” Remove it and reset the pet feeder and pair it again through the app.
How to reset sure feeder? ›
Reset the feeder to factory settings, holding down the Add Pet ( ) button for 10 seconds (until the light starts alternating red / green and the lid opens and closes).
How do I get my pet feeder back online? ›
If the router or internet is not working, try resetting the router or contact your internet provider. Power cycle the feeder by turning off the power switch. Wait 10 seconds and turn the power switch back on. Check for other devices near the feeder that use the internet or other wireless signals (such as a microwave).
Why is my PetSafe feeder blinking blue? ›
Blue Blinking Fast Feeder is trying to connect to Wi-Fi or is offline. Blue Solid Feeder is connected to Wi-Fi with internet and fully operational. White Blinking Reboot mode which triggers the feeder to attempt to reconnect to your Wi-Fi without losing the programmed settings.
How do you reset the smart life pet feeder? ›
On the front of the Smart Pet Feeder, you will find the 'feed' button. Press the 'feed' button for 5 seconds. When you hear a beep after about 5 seconds, this indicates that the reset has been performed successfully and the Smart Pet Feeder has been reset to factory settings.
How do you unlock an automatic pet feeder? ›
The buttons lock after 2 minutes of inactivity. The lock icon on the screen indicates that the buttons are locked. Press the center and up button at the same time to unlock the buttons.
Why does my PetSafe feeder keep going offline? ›
Ensure the feeder is connected to a 2.4 GHz network, not a 5 GHz network. Eliminating any Wi-Fi extenders and mesh networks may be necessary. If the feeder is connected to a dual-band router, it may be necessary to separate the Wi-Fi bands, so the feeder is connected only to the 2.4 MHz band.
Lift the PetSafe® cover on the top of the feeder. 3. Open both food tray lids by pressing down on the center of the PetSafe button for 5 seconds.
How do I reset my automatic feeder? ›
Press the Setting and OK buttons at the same time and hold for 3s until the feeder emits a beep, indicating the feeder has been reset.
How do I connect my pet feeder to Wi-Fi? ›
Click Add Device or + to add a new pet feeder. Choose the Add manually tab and select Wi-Fi Pet Feeder. Select 2.4 GHz Wi-Fi Network and enter password.
How do you reset a Petkit feeder? ›
If you do not need to use the device for an extended period of time, you must turn the device off yourself. At the same time, hold down the bowl reset button together with the manual food dispenser button for 5 seconds. After you hear relevant voice notification, you can let go.
How do I reset my smart life pet feeder? ›
The Smart Pet Feeder can be reset by pressing and holding the 'feed' button for 5 seconds until a sound is heard. A reset will erase all settings and data on the Smart Pet Feeder and return it to its original factory settings.
How to hard reset petlibro feeder? ›
Press and hold the Up button and the Down button for three seconds to reset the feeder to factory settings.
How to reset geeni smart pet feeder? ›
Press and hold reset button for 7 seconds until the blue light flashes to enter pairing mode. Geeni app should locate the smart feeder in no time. Use pet feeder in a dry indoor environment only.